Universal Fit (Professional Installation Recommended)
Fully Automatic Flush Mount
31" Replaceable Chrome Mast, 55" Cable, 11" Under Body
AM/FM Compatible Only
Not Compatible With CB Radios
Works Off The Radio's Power…
Electromag Hidden Antenna, designed for optimum AM/FM reception. Excellent solution for Streetrods, Show Cars, Classics or any vehicle where a conventional antenna is not desirable.
…
The advent of power accessories on automobiles through the 1950s and 1960s added a new premium driving experience to cars with functions at the press of the switch or button. A sleek, high-tech improvement to your classic or collector…
1969-1978 Corvette antenna mast retainer nut has 1/2 inch x 20 threads. Nut is 7/16 inch tall . Has 9/16 inch wrench flats. Top hole measures 0.414 inch ID.RETAINING RADIO AERIAL MAST…
This Corvette reproduction antenna nut has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your…
This die cast, chrome plated spacer is angled.
The short side is 1/4 inch tall.
The tall side is 7/16.
O.D. = 1 5/16
I.D. = 3/4
There is a flange at the bottom which fits/snaps into gasket 162039
There is also a locator pin…
Correct reproduction zinc diecast chrome plated antenna nut used on all 65-68 Corvettes.
This antenna nut cap has the correct flats on the side of the nut and stepped lower edge where the nut mounts on top of the antenna bezel.
Hole…
These are replacement mast assemblies for our RetroSound fully automatic power antennas. Included are the mast and gear assembly.
NOTE: These will not work with any other antennas except for RetroSound antennas
…
Antenna Assembly, Manual
Includes Ground Strap and Instructions
Retracts as Original
Exact Above Body Appearance as Original
Note: Does not include Nut, Bezel or Gasket as Shown in Photo
…
Reproduction Of Original
The mast section of the antenna consists of four round chrome sections, three telescoping sections, and one fixed section, with an approximately 1/4" ball-shaped tip at the end of the mast. The overall…
These OE-quality replacement antennas feature a chrome plated brass mast that is almost impervious to the elements and provides an improved ground plane for enhanced AM/FM reception.All metal mounting parts are used. Available with either…
These OE-quality replacement antennas feature a chrome plated brass mast that is almost impervious to the elements and provides an improved ground plane for enhanced AM/FM reception.All metal mounting parts are used. Available with either…
These OE-quality replacement antennas feature a chrome plated brass mast that is almost impervious to the elements and provides an improved ground plane for enhanced AM/FM reception.All metal mounting parts are used. Available with either…
If the antenna motor is still working, this kit will repair your antenna 99% of the time. Usually, the plastic flexible extension cable snaps, which obviously makes your antenna inoperative. This kit includes a new cable attached to the…
This antenna is an exact replacement for the Harada XM010. All the same quality as the original Harada unit. Top quality relay that controls the unit.
Universal Unit
5 Custom Head Kits, 4 Section Ext, 31"…
Don't replace your power antenna if all you need is the mast! Most power antenna units are needlessly replaced when a less expensive remedy could cure them. If the motor on your power antenna is still functioning, but your antenna mast is…
Reproduction Of Original
Direct Plug-In Connector
Used Only With Factory Wiring & Relay
Late Model Antennas Can Be Differentiated From Early Models By Noting That The Upper Antenna Nut Actually Holds The Top Of The Antenna In…
Each model is designed to work off the radio's power knob and can be used as a direct factory replacement or as an upgrade.NOTE:Fully automatic. A 31" mast and 55" cable. 11" under body. AM/FM compatible only.Requires Extension Cable - P/N…
Tapered mast as original (.100 at ball; .185 at mast).
Has correct .305 size ball.
This stainless steel antenna mast measures 31 1/2 inches overall length, with a thread size of 1/4 inch x 20.
…
Replacement Bezel
This Corvette replacement antenna bezel has been manufactured to meet or exceed factory specifications and performance. You will find the fit and finish will work perfectly for your Chevy.
…
1965-1966 Concours Power Antenna
Original Style Stainless Steel Mast that is Polished to a Chrome Line Finish
The First Mast Section has the Original Groove and Original Style Tip
Direct Coaxial Hookup, Power Lead, Hardware and…
This antenna cable is 186 inches long.
It is made from RG62U coax cable.
There is a threaded collar on one end to connect to the antenna itself.
*Correct cast nut
*The other end has a normal male connector to the radio.
*The collar is 9/16…